7. A force of 100 N acting on a body gives it a speed of 200 m/s in 2
sec. what is the mass of the body?
a. 1kg
b. 5 kg
c. 10kg
d. 15kg

Answers

Answer 1

Answer:

Choice a. 1 kg, assuming that all other forces on the object (if any) are balanced.

Explanation:

By Newton's Second Law,

[tex]\displaystyle a = \frac{\Sigma F}{m}[/tex],

where

[tex]a[/tex] is the acceleration of the object in [tex]\text{m}\cdot\text{s}^{-2}[/tex],[tex]\Sigma F[/tex] is the net force on the object in Newtons, and[tex]m[/tex] is the mass of the object in kilograms.

As a result,

[tex]\displaystyle m = \frac{\Sigma F}{a}[/tex].

Assume that all other forces on this object are balanced. The net force on the object will be [tex]100\;\text{N}[/tex]. The net force is constant. Acceleration should also be constant and the same as the average acceleration in the two seconds.

What is the average acceleration of this object?

[tex]\displaystyle \begin{aligned}\text{Acceleration} &= \text{Average Acceleration}=\frac{\text{Change in Velocity}}{\text{Time Taken}}\end{aligned}[/tex].

[tex]\displaystyle {a} = \frac{200\;\text{m}\cdot\text{s}^{-1}}{2\;\text{s}}=100\;\text{m}\cdot\text{s}^{-2}[/tex].

Apply Newton's Second Law to find the mass of the object.

[tex]\displaystyle m = \frac{\Sigma F}{a} = \frac{100\;\text{N}}{100\;\text{m}\cdot\text{s}^{-2}} = 1\;\text{kg}[/tex].

Answer 2

Answer:

a.1kg

Explanation:


Related Questions

State the 3 laws of motion

Answers

Answer:

Explanation:

Newton's first law of motion:

An object in motion stays in motion, and an object at rest stays at rest, until acted upon by an unbalanced force.

Newton's second law:

The net force on an object is equal to its mass times its acceleration.

Newton's third law:

For every action, there is an opposite and equal reaction.

what is the coefficient for titanium tetrachloride when the equation below is balanced?

Answers

the coefficient of TiCl4 would be 1

Please help I’m a big stupid idiot head

Answers

Answer:

Explanation:

ur right i think

Ur right gimme brainlyest

A rock is dropped from a vertical cliff. The rock takes 6.00 s to reach the ground below the cliff. What is the height of the cliff? (take g=10.0 m/s2)

Answers

Answer:

180 m

Explanation:

The rock follows a free-fall motion - so the vertical distance covered can be found by using the equation

[tex]h=\frac{1}{2}gt^2[/tex]

where

g = 10 m/s^2 is the acceleration due to gravity

t = 6.00 s is the time of the fall

Substituting these data, we find the height of the cliff:

[tex]h=\frac{1}{2}(10 m/s^2)(6.00 s)^2=180 m[/tex]

Final answer:

The height of the cliff from which the rock is dropped can be calculated using the formula h = 0.5*g*t². This gives us a calculated height of 180 meters.

Explanation:

The problem you're dealing with is related to one of the basic physics equations of motion, specifically for an object under constant acceleration - in this case, the acceleration due to gravity. To find the height of the cliff, we can use the formula h = 0.5*g*t², where 'h' is the height, 'g' is the acceleration due to gravity (10.0 m/s² as provided), and 't' is the time it takes for the rock to hit the ground (6.0 seconds in this problem).

Plugging in the known values into the equation gives us h= 0.5*10.0*(6.0)² = 180.0 meters. This means the cliff is approximately 180 meters high.

Learn more about Motion under Gravity here:

https://brainly.com/question/28554700

#SPJ3

The phase of mitosis during which the chromosome pairs line up

along the middle, or the equator, of the cell is called



a. anaphase

b. prophase

c. telophase

d. metaphase
\


Never mind. I got the answer, it was d

Answers

Yep the answer is d

Metaphase is characterized by sister chromatids lining up at the cell's equator, on a plane known as the metaphase plate, preparing for separation during anaphase.

Metaphase is the second stage of mitosis. During this stage, the sister chromatids, with their attached microtubules, line up along a linear plane in the middle of the cell. This is known as the metaphase plate, a plane through the center of the spindle on which the sister chromatids are positioned. The spindles, emerging from centrosomes at either end of the cell, are poised to pull apart the sister chromatids and distribute one from each pair to each side of the cell. The chromosomes are maximally condensed at this time, ensuring efficient separation during the subsequent phase of anaphase.

What is the vector product of two vectors????

Answers

Answer:

The magnitude of the vector product of two vectors can be constructed by taking the product of the magnitudes of the vectors times the sine of the angle (<180 degrees) between them. The magnitude of the vector product can be expressed in the form: and the direction is given by the right-hand rule.

Answer:

The vector product of two vectors is a vector perpendicular to both of them. Its magnitude is obtained by multiplying their magnitudes by the sine of the angle between them.

Caleb is swinging Rachel in a circle with a centripetal force of 533 N. If the radius of the circle is 0.75 m and Rachel has a mass of 16.4 kg, how fast is Rachel moving? Round to the nearest tenth. m/s

Answers

Velocity = √((Centrifugal force *  radius)/mass)

Velocity = √(533 * 0.75 / 16.4)

Velocity = √(399.75 / 16.4)

Velocity = √24.375

Velocity = 4.9 m/s

Answer:

4.9

Explanation:

I just did it

Describe the relationship between electricity and magnetism.

Sample Response: Electrical and magnetic fields occur together. A change in current induces a magnetic field. A change in magnetic field induces a current.

Answers

Answer:In the similar way, a changing magnetic field produces an electric current in a wire or conductor. The relationship between electricity and magnetism is called electromagnetism.

Explanation:

Final answer:

Electricity and magnetism are closely related, where changing electric currents produce magnetic fields and changing magnetic fields induce electric currents. This principle, known as electromagnetism, is fundamental to many technologies and reflects an underlying symmetry in nature.

Explanation:

The interconnection between electricity and magnetism is a cornerstone of the field of electromagnetism. These two phenomena are so intertwined that a change in electric current can produce a magnetic field, and conversely, a change in a magnetic field can induce electric current. This concept is crucial to many technological advances such as generators, transformers, and various electronic devices that are essential to modern life.

For instance, when an electric current flows through a wire, it creates a surrounding magnetic field. If this magnetic field varies, it can induce a current in another nearby circuit, a principle known as magnetic induction. This is the fundamental process behind the operation of electrical generators and transformers. Historical experiments, including those by scientists such as Michael Faraday and Joseph Henry, have shown that electricity can produce magnetism and vice versa.

Hansel pushes a 2 lb. box 5 feet in 20 seconds. How much work has he done?

Answers

Work = force x distance

You can see time doesn’t matter (if we were talking about power, which is the RATE at which work is performed, that would be a different story).

W = 2 x 5 = 10 foot-pounds of work

Foot-pounds are gross units. Better to work in SI units when you can!

Answer:

10

Explanation:

Which is not a form of light?

Answers

Radio waves, Middle-C, and halitosis are not forms of light.

All of the above are forms of light. Therefore, the correct option is option D among all the given options.

What is light?

Light as well as visible light is electromagnetic that is visible to the human eye. Here between infrared and ultraviolet ranges, visible light is commonly defined as having wavelengths of 400-700 nanometres (nm) or frequencies of 750-420 terahertz.

In physics, the term "light" can be used to more broadly characterize electromagnetic radiation of any wavelength, whether visible or not. Gamma rays, X-rays, microwaves, and radio waves are all forms of light in this sense. All of the above are forms of light.

Therefore, the correct option is option D.

To know more about light, here:

https://brainly.com/question/30749500

#SPJ6

Your question is incomplete but most probably your full question was,  

Which of the following is not a form of light?

A) radio waves

B) microwaves

C) x-rays

D) All of the above are forms of light.

E) None of the above is a form of light

Hans Selye’s general adaptation syndrome theory proposes that adaptation to stress occurs in how many stages?

Answers

Answer:

Adaption to stress occurs in three stages: alarm, fight or flight, exhaustion.

Explanation:

According to the general adaptation syndrome theory proposed by Hans Selye, the adaption to stress occurs in three stages which are:

1. alarm

2. fight or flight

3. exhaustion

This is a process which comprises of three stages that describes the physiological changes which a body undergoes when in stress (an emotional, mental and physical human response to a specific stimulus).

Final answer:

Hans Selye’s general adaptation syndrome theory proposes three stages of stress response: alarm reaction, stage of resistance, and stage of exhaustion. These stages depict how our body physiologically reacts and adapts to stressful situations.

Explanation:

Hans Selye’s general adaptation syndrome theory proposes that adaptation to stress occurs in three stages. These stages include the alarm reaction, where the body's immediate reaction to a stressful situation occurs, the stage of resistance, where the body begins to adjust to the stressor, and the stage of exhaustion, where the body's resources become depleted due to prolonged exposure to the stressor. Understanding these stages can help individuals better manage and respond to stressors in their lives.

Learn more about General Adaptation Syndrome here:

https://brainly.com/question/33560674

#SPJ3

in which region of the sun does energy move as waves that transfer from atom to atom

Answers

Answer:

Radiative zone

Answer:photosphere corona core radiative zone chromosphere convective zone. Radiative zone of the Sun does energy move as waves that transfer from atom to atom.

Explanation:photosphere corona core radiative zone chromosphere convective zone. Radiative zone of the Sun does energy move as waves that transfer from atom to atom.

1. The speed and direction with which an object moves is its

Answers

It’s called velocity. Velocity is a vector quantity so it’s basically the same thing as speed but the difference is it’s speed in a certain direction.

Answer:

The speed and direction with which an object moves is its velocity.

Explanation:

Velocity is the speed of an object with a given direction.

Hope this helps.

Which of the following has the greatest momentum?
A. a tortoise with a mass of 275 kg moving at a velocity of 0.55 m/s
B. a hare with a mass of 2.7 kg moving at a velocity of 7.5 m/s
C. a turtle with a mass of 91 kg moving at a velocity of 1.4 m/s
D. a roadrunner with a mass of 1.8 kg moving at a velocity of 6.7 m/s

Answers

Answer:

A

Explanation:

Momentum is mass times velocity.

A. 275 kg × 0.55 m/s = 151.25 kgm/s

B. 2.7 kg × 7.5 m/s = 20.25 kgm/s

C. 91 kg × 1.4 m/s = 127.4 kgm/s

D. 1.8 kg × 6.7 m/s = 12.06 kgm/s

So A has the greatest momentum.

Momentum of a body is the product of the mass of the body and its velocity. The momentum of the tortoise is greatest. Thus  option A is the correct option.

What is momentum?

Momentum of a body is the product of the mass of the body and its velocity. It can be given as,

[tex]p=mv[/tex]

Given options are,

A) A tortoise with a mass of 275 kg moving at a velocity of 0.55 m/s

The mass of the tortoise is 275 kg.

The velocity of the tortoise is 0.55 m/s.

Thus momentum of tortoise,

[tex]p_a=275\times0.55\\p_a=151.25[/tex]

Hence the momentum of the tortoise is 151.25 kg-m per second.

B) A hare with a mass of 2.7 kg moving at a velocity of 7.5 m/s

The mass of the hare is 2.7 kg.

The velocity of the hare is 7.5 m/s.

Thus momentum of hare,

[tex]p_b=2.7\times7.5\\p_b=20.25[/tex]

Hence the momentum of the hare is 20.25 kg-m per second.

C) A turtle with a mass of 91 kg moving at a velocity of 1.4 m/s

The mass of the turtle is 91 kg.

The velocity of the turtle is 0.14 m/s.

Thus momentum of turtle,

[tex]p_c=91\times1.4\\p_c=127.4[/tex]

Hence the momentum of the turtle is 127.4 kg-m per second.

D) A roadrunner with a mass of 1.8 kg moving at a velocity of 6.7 m/s

The mass of the roadrunner is 1.8 kg.

The velocity of the roadrunner is 6.7 m/s.

Thus momentum of roadrunner,

[tex]p_d=1.8\times6.7\\p_d=12.06[/tex]

Hence the momentum of the roadrunner is 12.06 kg-m per second.

Hence the momentum of the tortoise is greatest. Thus  option A is the correct option.

Learn more about the momentum here;

https://brainly.com/question/4956182

What is the most significant factor in determining kinetic energy?

Answers

Answer:

The velocity

Explanation:

Kinetic energy of an object is directly proportional to the square of its velocity if mass if kept constant. Therefore, if the velocity is doubled the kinetic energy increases four times.

K.E= 1/2mv²

m is the mass of the object and v the velocity. This means that there must be motion for there to be kinetic energy.

3. Which subatomic particle(s) determines an atom's atomic number?

Answers

Answer:

The remainder of the hydrogen atom's mass comes from the positively charged proton. The atomic number of an element is the number of protons in its nucleus. Neutrons are neutral particles having a mass slightly greater than that of the proton. Different isotopes of the same element contain the same number of protons but differing numbers of neutrons.

Explanation:

The motion of an object thrown at an angle is__ motion.

Answers

The motion of an object thrown at an angle is projectile motion

Projectile(missile designed to be fired from rocket)

To balance a chemical equation we use______.
-coefficients
-subscripts

Answers

Answer:

Coefficients

Explanation:

Coefficients are used to balance chemical equations.According to the law of conservation of mass, the mass of the reactants in a chemical equation should be equivalent to the mass of the products.The conservation of mass is achieved in chemical equations is achieved through balancing chemical equations. Balancing chemical equations is a try and error of putting appropriate coefficients to the reactants or products to ensure that the number of atoms of each element are equal on the side of the reactants and that of products.

An alien spaceship is 8*10^14 m away sends us a radio wave signal. How long does it take for the signal to reach us?

Answers

Answer:

[tex]2.67\cdot 10^6 s[/tex]

Explanation:

The radio signal travels to us at the speed of light, so at a speed of

[tex]c=3.0\cdot 10^8 m/s[/tex]

The distance between the spaceship and the Earth is

[tex]d = 8\cdot 10^{14}m[/tex]

Since the signal travel by uniform motion, we can write

[tex]d = vt[/tex]

where

t is the time the signal needs to reach the Earth

By solving the equation for t, we find

[tex]t=\frac{d}{v}=\frac{8\cdot 10^{14} m}{3.0\cdot 10^8 m/s}=2.67\cdot 10^6 s[/tex]

HOW DO PROTONS, NEUTRONS AND ELECTRONS DIFFER?

Answers

Protons are positively charged and neutrons are neutral whereas electrons are negatively charged.

The protons has the positive charge, neutron has no charges and electrons have the negative charge.

Explanation:

The basic difference between the particles of the atom are their charges and their orientation in the atom. The proton and the neutron are present in the nucleus of the atom whereas the electrons are at the periphery of the atom. The nucleus is stationary in orientation having proton and neutron in it, whereas the periphery as the electrons are moving. Electrons revolves around the nucleus.

Which units are used to express kinetic energy?

meters

seconds

joules

newtons

Answers

Answer:

The SI units for energy is Joules.

Answer: Joules

Hope This Helps, Please Vote Brainliest!!

Plz help, it for my science CFE.

Which of the following four fundamental forces is responsible for binding protons and neutrons together in the nucleus?

A. Electromagnetism
B. Weak nuclear force
C. Gravity
D. Strong nuclear force

Answers

Answer: The strong nuclear force.

Explanation: The strong force holds the protons and neutrons together in the nucleus. Despite being the strongest force, it has a very small range. (Think about how small an atom is) The strong force is thought to occur due to the exchange of pions between the protons and the neutrons. Since pions have a very short lifespan, the protons and neutrons must be very close to each other in order to exchange them. This phenomenon is what keeps the protons and neutrons so tightly binded together in the nucleus.

A 60.0 kg runner is moving at 6.00 m/s and speeds up to 9.00 m/s. The runner’s change in kinetic energy is 1,350 J.


Answers

Hello i hope you are having a good day :) Question : A 60.0 kg runner is moving at 6.00 m/s and speeds up to 9.00 m/s. The runner’s change in kinetic energy is 1,350 J? = firstly you would need to change the kinetic energy meaning that would be a kinetic energy of 1/2mv^2  so now you would do the m which would be for the mass and the v is the velocity as well the initial of k.e that would be 1/2 x 60 x 6^2 that would equal too = 1,080j Final K.E = 1/2 × 60 × 9² = 2,430 J Work done = change in kinetic energy. = 2,430 - 1,080 = 1,350 J. Hopefully that helps you.

The change in the kinetic energy of the runner will be 1350 J. It is found by subtracting the kinetic energy during two different velocity.

What is kinetic energy?

The energy of the body by the virtue of its motion is known as the kinetic energy of the body. It is defined as the product of half of mass and square of the velocity.

According to the law of conservation of energy, the total energy is defined as the sum of kinetic energy and potential energy.

The change in the kinetic energy is found as;

[tex]\rm KE = \frac{1}{2} m(v^2-u^2)\\\\ KE = \frac{1}{2} \times 60 (9^2-6^2) \\\\ KE=1350 \ J[/tex]

Hence, the change in the kinetic energy of the runner will be 1350 J.

To learn more about kinetic energy, refer to the link;

brainly.com/question/999862

#SPJ2

When work is measured in joules and time is measured in seconds power is measured in kilograms true or false

Answers

Hello!

The answer is:

False, the power measured is equivalent to Watt.

Why?

The power is the rate which a determinate amount of work is done, being this, the amount of work done over time, which is also equal to the energy used over time.

We can calculate the power using the following formula:

[tex]Power=\frac{Work}{Time}[/tex]

Where,

Power, is quantity of energy used over time, measured in Watt.

Work, is the energy transferred when an object is in motion, covering a distance, it's measured in Joules (N.m)

Time, is the time measured in seconds.

Have a nice day!

This position-time graph describes an object's motion. Use it to determine the
displacement (in m) of the object after 6.0 seconds of motion. Enter the
appropriate + or - sign.

Displacement=?​

Answers

We're happy that you're asking for the "displacement", because displacement is simply the straight-line distance between the start-point and end-point, and we don't care about any of the motions or gyrations along the way.

From the graph:

-- The location of the object at time-zero, when time begins, is  10 meters.

-- The location of the object after 6.0 seconds is  4 meters.

-- The distance between the start-point and end-point is

(final location) - (initial location)

-- So Displacement = (4 meters) - (10 meters)

Displacement = -6 meters

The displacement of the object from starting to endpoint is

[tex]d=+6m[/tex]

From the question we are told that:

Displacement Time t=6sec

Displacement

Displacement is simply the distance between the starting point and the endpoint.We do not make reference to variant distances covered just the starting and endpoint.

Generally, the equation for Displacement is mathematically given by

[tex]D=x-y[/tex]

Where

x=starting point

y= endpoint.

Therefore

[tex]d=10-4[/tex]

[tex]d=+6m[/tex]

In conclusion

The displacement of the object from starting to endpoint is

[tex]d=+6m[/tex]

For more information on this visit

https://brainly.com/question/12874363

temperatures expressed in the kelvin scale are _____ higher than temperatures in the celsius scale.

a. 460°
b. 200°
c. 283°
d. 273°

Answers

Answer: d

Explanation:

Celsius temperatures can be negative while kelvin goes down to absolute zero and doesn’t go any lower, thus no negative numbers

Answer:

option (D)

Explanation:

The melting point of ice is 0 degree and the boiling point of water is 100 degree on Celsius scale. There are 100 divisions between the melting point and the boiling point.

The melting point of ice is 273 degree and the boiling point of water is 373 degree on Kelvin scale. There are 100 divisions between the melting point and the boiling point.

The relation between the Celsius scale and the Kelvin scale is

[tex]\frac{C - 0}{100}= \frac{K - 273}{100}[/tex]

So, K = C + 273

If a force of 10 N applied to an object with a mass of 1 kg, what is the acceleration of the object?​

Answers

Answer:

10 m/s²

Explanation:

Newton's second law:

∑F = ma

10 N = (1 kg) a

a = 10 m/s²

1. Which quantity is the transfer of energy?
work
motion
force

Answers

Answer:

work

Explanation:

Work is the transfer of energy by a force to another object. Energy is transferred when a force causes an object to be displaced.

Work is defined as the transfer of energy by a force. When a force is applied over a distance, work is done, and energy is transferred from one object to another. Work is measured in joules, with 1 joule being equivalent to 1 newton-meter.

Calculate the total resistance for a 650ohm , a 350 ohm , and a 1000 ohm resistor connected in series

Answers

Answer:

2000 ohms

Explanation:

Resisters in series just add.

Rt = R1 + R2 + R3

R1 = 650 ohm

R2 = 350 ohm

R3 = 1000 ohm

Rt = 650 + 350 + 1000

Rt = 2000 ohms.

The total effective resistance of several resistors in SERIES is just the sum of all the individual resistances.  

So the effective resistance of 650Ω,  350Ω,  and  1,000Ω  in series is

Sum = (650Ω + 350Ω + 1,000Ω)

Sum = 2,000 ohms

a wave travels at a speed of 793 m/s and has a wavelength of 2.3 meters. calculate the frequency of the wave​

Answers

Answer:

344.8 Hz

Explanation:

The frequency of a wave is given by:

[tex]f=\frac{v}{\lambda}[/tex]

where

v is the speed of the wave

[tex]\lambda[/tex] is its wavelength

Here we have

v = 793 m/s

[tex]\lambda=2.3 m[/tex]

Substituting into the equation, we find

[tex]f=\frac{793 m/s}{2.3 m}=344.8 Hz[/tex]

Other Questions
A hockey puck is set in motion across a frozen pond. If ice friction and air resistance are neglected, the forcerequired to keep the puck sliding at constant velocity isA) the weight of the puck divided by the mass of the puck.B) the mass of the puck multiplied by 9.8 meters per second per second.C) qual to the weight of the puck.D) zero newtons.E) none of these. Why would someone become an indentured servant?OA. To receive a free trip to AmericaOB. To develop trade relationshipsTo become a master craftsmanOD. To be elected to public office the concession stand sells hot dogs for $3 and burger for $4. at last weeks football game, the stand sold 10 more hot dogs than burgers and made $184. write a system of equation to represent the situation j'ai une PE argumentative sur la violence inconvenients et avantages et je veux quelques arguments pour ma PE. aidez moi!!! Which of the following uses the operators and, or, and not to get more exact search results? A. Boolean logicB. Google logicC. Search logicD. Research logic what is the main difference between an internal combustion engine and an external combustion engine? PLEASE ANSWER ASAPA) The burning of fuel occurs inside the cylinder with the piston in an external combustion engine. B) The burning of fuel occurs inside the cylinder with the piston in an internal combustion engine. C) An internal combustion engine doesnt have a cylinder and a piston. D) An external combustion engine doesnt have a cylinder and a piston find the correct trigonometry formula to solve for X. Find (f*f)(3)f(x)=x^2-xA. 30B. 6C. 33D. -6 A grocery, a cafe, a boutique, and a dance studio have the addresses 500 Elm, 524 Elm, 538 Elm, and 544 Elm, but not necessarily in that order. The boutique is between the cafe and the studio. The studio has the highest address. The grocery is between the cafe and boutique. Write a polynomial function in standard form with zeros at 0,1 and 2. PLEASE HELP!!! A. F(x)=x(x+1)(x+2)B. F(x)=x(x-1)(x-2)C. F(x)=x^3+3x^2+2xD. F(x)=X^3-3x^2+2x Were there more producers than consumers and more consumers than predators on your pyramid? Why or why not? Were there any that could have fit in more than one category? Once glucose enters the body's cells, it is used to provide energy. What are the two main life processes for which that energy is used? Which of the following would be used to determine the probability of three independent events in order?-Sum rule-Product rule-Chi-square test-Binomial expansion-Random sampling error A Sample Of Oxygen Gas Is Collected Over Water At 22C And 98.67 KPa Pressure. If The Partial Pressure Of The Water Is 2.67 KPa, The Partial Pressure Of The Oxygen Is? In order to calculate the number of neutrons you must subtract the ______ from the ________. The playlist consists of 21 songs by The Working Mamas, 12 songsby Chef Mo Cheese, 36 songs by The Snippers, 54 by Lucy andThe Jungle Cats, and 27 by Nuestra Paradise.What's the probability of Chef Mo Cheese playing?Write the answer as a percent.artist. What causes changes in weather? a. Air masses move and meet. c. Water evaporates. b. The air gets more humid. d. Clouds form. write a 5 paragraph essay on ancient Rome. p.s literally anything about ancient Rome. 13.Imagine you are working as a Medical Administrative Assistant at a local hospital in your neighborhood. Its your first day of work at your new job and you are excited to get to work and learn as much as you can. However, shortly after arriving at work, you discover that there has been a miscommunication with HR about your start date. The office was expecting you to start the following day instead. As a result, your login information for the offices computer system has not been created just yet, and the person responsible for training you is on Paid Time Off (PTO). Explain how would you expect a manager to use the 5 Step Process introduced during this week in order to resolve this miscommunication problem. Provide specific reasons for each step and answer as detailed as possible. All the 5 stepsStep 1: What is the problem?Step 2: What are the alternatives?Step 3: What are the advantages and/or disadvantages of each alternative?Step 4: What is the solution?Step 5: How Well is the solution working? A set of data with a mean 56 and a standard deviation 3.3 is normally distributed. find 2 standard deviations from the mean Steam Workshop Downloader