Answer:
option B
Explanation:
The correct answer is option B
Carbon/graphite fiber composite is a polymer composite which is five times stronger than the mild steel and five-time more lighter than it.
This material has a high-temperature resistant quality, it works as a high insulator. The material does not melt at high temperatures. And the material is also corrosive resistant but has a corrosive effect when contact with aluminum.
Hence, we can say that Carbon/graphite fiber has high stiffness, high compressive strength, and have a corrosive effect in contact with aluminum.
Final answer:
Carbon/graphite fiber composites are known for their stiffness, high compressive strength, and ability to conduct electricity, characteristics derived from the structure of graphite itself.
Explanation:
The characteristics of carbon/graphite fiber composites are influenced by the structure of graphite itself. Graphite is structured in layers of carbon atoms connected in a hexagonal lattice. Each carbon atom in graphite forms three σ bonds with neighboring carbon atoms using sp² hybridized orbitals, and the fourth unhybridized p orbital participates in bonding, spreading the electron density over the entire layer, which allows the material to conduct electricity.
Due to the weak van der Waals forces holding the layers together, graphite is soft and has lubricating properties, allowing the layers to slide over each other easily. This structural characteristic of graphite is crucial in forming composites that often possess properties such as stiffness, high compressive strength, and the ability to conduct electricity.
When stopped at an intersection and your light turns green, you should __________ before accelerating.
A: look right then left
B: look left then right
C: look left then right then left again
D: look straight ahead
E: look behind you
Answer:
C: look left then right then left again
Explanation:
At an intersection, there three routes, the left, the right and straight ahead.
For a car stopped at an intersection, once the light turn green, it is advisable that the driver should watch the left and right then left again before accelerating. This is because there might be any car coming from any of the sides unnoticed which might leads to accident especially the first side u looked at (left) must be take much cognisance of hence the need to look left again before accelerating.
Final answer:
When stopped at an intersection and your light turns green, you should A. look right and then left before accelerating.
Explanation:
When stopped at an intersection and your light turns green, you should look left, then right, then left again before accelerating. This practice ensures that you are aware of any vehicles that may not have stopped at their red light or are trying to beat a yellow light, as well as any pedestrians or cyclists that may be crossing.
Remember that while traffic signals are there to regulate flow, driver vigilance is crucial in preventing accidents and ensuring safety. Thus, it is important to check both directions to ensure the intersection is clear before proceeding. Safe driving practices include being cautious and aware of potential risks on the road.
An autotransformer is used to reduce the voltage of a 100-kilovolt amp, 480-volt secondary of an isolated type transformer, to supply a 100-kilovolt amp load with 277 volts. What size autotransformer is needed? (Use the co-ratio to determine the size.)
An autotransformer is a type of electrical transformer that has only one winding, and portions of the same winding act as both the primary and secondary winding sides of the transformer. A 33.9 kVA autotransformer is needed to reduce the voltage of a 100-kilovolt amp, 480-volt secondary of an isolated type transformer to supply a 100-kilovolt amp load with 277 volts, using the co-ratio method.
To determine the size of an autotransformer needed to reduce the voltage of a 100-kilovolt amp, 480-volt secondary of an isolated type transformer to supply a 100-kilovolt amp load with 277 volts, we can use the co-ratio method.
The co-ratio is the ratio of the number of turns on the primary winding to the number of turns on the secondary winding of the transformer.
Secondary voltage: 480 V
Load voltage: 277 V
Load current: 100 kVA
To calculate the co-ratio, we can use the formula:
Co-ratio = Secondary voltage / Load Voltage
Co-ratio = 480 V / 277 V
Co-ratio ≈ 1.734
The co-ratio is approximately 1.734. To determine the size of the autotransformer needed, we can use the formula:
Size of autotransformer = Load kVA / (Co-ratio)²
Size of autotransformer = 100 kVA / (1.734)²
Size of autotransformer ≈ 33.9 kVA
Therefore, a 33.9 kVA autotransformer is needed to reduce the voltage of a 100-kilovolt amp, 480-volt secondary of an isolated type transformer to supply a 100-kilovolt amp load with 277 volts, using the co-ratio method.
To know more about autotransformers:
https://brainly.com/question/34694881
#SPJ12
To supply a 100 kilovolt-ampere load with 277 volts from a 480-volt secondary, an autotransformer that is roughly 1.73 times smaller than the original isolated type transformer is required. The size calculation is derived from the co-ratio (the ratio of primary to secondary voltages), which here equals to 480/277 = 1.73.
Explanation:The subject in question is regarding the use of an autotransformer, specifically, what size is needed to reduce the voltage from 480 volts to 277 volts in order to supply a 100 kilovolt-ampere load. First, we need to handle the co-ratio. The co-ratio of a transformer is the ratio of primary to secondary voltages, often used to calculate the size of a transformer. In this case the co-ratio would be 480/277 = 1.73.
Utilizing the transformer equation, we can comprehend that the voltage reduction from 480 to 277 volts that undergoes in an autotransformer proposes a comparable reduction in size of the transformer. Based on this, the autotransformer needed should be around 1.73 times smaller than the original isolated type transformer.
As a brief primer on the functioning of the transformers, they operate on the principle of electromagnetic induction and are used in power distribution systems to step-up or step-down the voltages. This allows the efficient transmission of power over long distances and also the provision of the correct voltage levels suitable for different uses.
Learn more about Transformers and Autotransformer Sizing here:https://brainly.com/question/32456416
#SPJ12
Some cities now implement signal lights designed to specifically apply to _____ rather than motorized vehicles.
A) Pedestrians
B) Trucks
C) Bicycles
D) Motorcycles
E) All of the above
The correct answer is C; Bicycles.
Further Explanation:
In major cities, in the United States, have implemented signal lights specifically designed for bicycle riders. The riders also have their own designated bike lanes in many large cities. Drivers in vehicles, are to give the right of way to people on bicycles.
Bicycle riders are to follow the same laws and laws specifically for the riders or they can face fines and tickets.
Learn more about bicycle laws at https://brainly.com/question/8934107
#LearnwithBrainly
Julie runs 2 miles every day after school because it reduces the stress she feels from schoolwork. Julie's running habit is maintained by a ________ reinforcer.
Answer:
negative
Explanation:
The term reinforce means to strengthen, and is used in psychology to refer to any stimulus which strengthens or increases the probability of a specific response.
Negative Reinforcement can be seen as the act of taking something negative away in order to increase a response.
Julie runs 2 miles every day after school because it reduces the stress (negative) she feels from school work (in order to increase her response in her school work).
In which one of the following circumstances could mechanical energy not possibly be conserved, even if friction and air resistance are absent?
A car moves down a hill, its velocity continually increasing alongthe way.
A car moves up a hill at a constant velocity.
A car moves along level ground at a constant velocity.
A car moves up a hill, its velocity continually decreasing alongthe way.
Answer:
A car moves up a hill at a constant velocity
Explanation:
Since the velocity is constant, the speed is also constant and so is the kinetic energy. However, total mechanical energy is sum of gravitational potential energy and kinetic energy, and the car is moving up the hill so its potential energy rises.
Thus, in the circumstances described the mechanical energy cannot be conserved.
The correct answer is A car moving up the hill with constant velocity.
When driving through standing water at high speed water may build up beneath the wheels and cause the vehicle to skid is commonly referred to as:________
Answer: Hydroplaning
Explanation: Hydroplaning is the skiding of a high speed vehicle when water builds beneath the wheels when driving through standing water.
It is usually caused by factors such as High speed,Standing water,deflated tyres. It is strongly recommended that when driving in standing water a driver should drive at a slow and steady speed and always to ensure that the vehicle tyres are adequately inflated with air,this is one of the causes of vehicular accidents during rainy season or flood.
A falling object of weight 10 N encounters 10 N of air resistance. The net force on the object is____________.
An object of weight 10 N that is falling on the ground, and it experiences a 10 N air resistance, then the net force on the object will be 0 N.
What is Force?A force in physics is an input that has the power to change an object's motion.
A mass-containing object's velocity can vary, or accelerate, as a result of a force. Intuitively, a push or a pull can also be used to describe forces. Being such a vector quantity, a force does have magnitude and direction. The SI unit metric newton is used to measure it (N). The letter F stands for force.
According to Newton's second law's original formulation, an object's net force is equal to the speed that its momentum is changing over time.
As per the given information in the question,
Weight of the object = 10 N
Friction due to air resistance = 10 N
Then, the net force will be,
10 N - 10 N = 0 N
Therefore, the net force will be 0 N.
To know more about Force:
https://brainly.com/question/13191643
#SPJ5
The net force on the object is zero.
When an object is falling, it experiences two main forces: gravity (its weight) pulling it downward and air resistance pushing upward. In this case, the object has a weight of 10 N (newtons), which is a force acting downward due to gravity, and it encounters 10 N of air resistance, which is a force acting upward against the motion of the falling object.
To find the net force on the object, you need to calculate the difference between the two forces:
Net Force = Weight - Air Resistance
Net Force = 10 N - 10 N
Net Force = 0 N
So, the net force on the object is 0 N. This means that the forces of gravity and air resistance are equal in magnitude and opposite in direction, resulting in a net force of zero. In this situation, the object is in a state of dynamic equilibrium, and its velocity remains constant (it doesn't accelerate further).
Learn more about net force here:
https://brainly.com/question/14361879
#SPJ3
Antoinette was diagnosed with hypertension, a noncommunicable disease in which her blood pressure is higher than normal. What is the most likely explanation for why she is hypertensive? She was obese and had a diet high in salt intake. She did not wash her hands enough. She was bitten by a mosquito. She was never vaccinated against hypertension.
Answer:
She was obese and had a diet high in salt intake.
Explanation:
higher blood pressure is condition known as hypertension which is the main cause of many heart problems which can be life threatening. In obese people. high level of fats inside the blood vessels which can cause blockage inside and can lead to heart problems.
high concentration of salts intake also disturbs the salts concentration in the blood vessels. The disturbance in salt concentration is the function of the kidney to remove it. the increase concentration also cause increase in blood pressure which leads to hypertension.
Answer:
She had a diet high in salt intake.
Explanation:
Sodium is medically known to raise blood pressure.
Washing hands and mosquitos are not related to blood pressure.
There is no vaccination against high blood pressure.
A spring has an equilibrium length of 2.0 meters and a spring constant of 10 newtons/meter. Alice is pulling on
one end of the spring with a force of 3.0 newtons. Bob is pulling on the opposite end of the spring with a force of
3.0 newtons, in the opposite direction. What is the resulting length of the spring?
(A) 1.7 m
(B) 2.0 m
(C) 2.3 m (correct answer)
(D) 2.6 m
(E) 8.0 m
Final answer:
When equal forces of 3.0 newtons are applied on both ends of a spring with an equilibrium length of 2.0 meters, the resulting length of the spring remains 2.0 meters because the forces cancel each other out.
Explanation:
To find the resulting length of the spring, we should first determine the amount of stretch or compression caused by the forces applying on the spring. Since Alice and Bob are both pulling with a force of 3.0 newtons each in opposite directions, the net force on the spring is zero. Therefore, the spring neither stretches nor compresses from its equilibrium length.
The spring has an equilibrium length of 2.0 meters and remains at this length because the forces applied by Alice and Bob cancel each other out. So, the resulting length of the spring when 3.0 newtons is applied at each end in opposite directions is 2.0 meters, which is answer (B).
Water can pile up a short distance above a container's rim due to: a. high capillary action. b. low viscosity. c. low surface tension. d. high surface tension. e. high viscosity.
Answer: a. high capillary action.
Explanation:
Water can pile up a short distance above a container's rim due to high capillary action. Capillarity is process by which water falls or rise through a narrow capillary tube. The concept allows water to rise to a certain height through the container before dropping.
A fan connected to a 120-volt electrical system by an extension cord was worn through and exposed the bare, energized conductor, which made contact with the ladder. The ground wire was not attached to the male end of the cord's plug. When the energized conductor made contact with the ladder, the path to ground included the worker's body, resulting in death. What contributed to the electrocution?
Answer:
The worker completed the circuit.
Explanation:
Thinking process:
Electricity is the flow of electrons in a circuit. There is one condition for the electrons to flow - the completion of a circuit. In order for that to be established, there must be a side with low electron concentration or affinity for electrons.
The earth has an infinite affinity for electrons. Thus, earth wires are used to channel an excess amount of electrons there. This prevents the short circuiting injuring a person. Hence, a three-pin plug.
Because there was not insulation, like rubber, an alternative pathway could not be found for electrons. Hence the worker was electrocuted as the electric current passed through him.
The electrocution occurred due to a lack of proper safety measures, specifically an improper grounding connection. When the bare, energized conductor of the fan connected with the ladder, the electrical current sought the path of least resistance to ground which included the worker's body.
Explanation:The factors contributing to the fatal electrocution in this scenario are mainly faulty or inadequate safety measures and the behavior of electricity. Electricity always seeks the path of least resistance to the ground and in the absence of a proper ground wire connection, the electricity from the exposed conductor of the extension cord sought alternative grounding routes, in this case, through the worker's body.
Thermal and shock hazards are two primary dangers of electricity. A thermal hazard can cause fires due to excessive electric power resulting in unwanted thermal effects. A shock hazard is where electric current passes through a person, potentially causing harm ranging from a mild shock to death.
The system lacked a vital safety feature, which is a functioning ground connection. A three-wire system that includes live, neutral, and ground wires helps to avoid such scenarios. With a proper ground connection, any fault currents would be safely directed to the ground, and a circuit breaker would usually trip, cutting off the electricity. In this case, the lack of a proper ground connection contributed to the fatal electrocution.
Learn more about Electrical Safety here:
https://brainly.com/question/34518143
#SPJ3
What is the average cost for a severe injury in a collision?
A. $4,000
B. $15,000
C. $47,000
D. $247,000
Answer:
D
Explanation:
According to research and data, the average cost for a severe injury in a collision is $247,000.
These include traumatic brain injury, severe damage to limbs which could result to loss of the limbs, spinal cord injuries that could result to partial or total paralysis as well as internal damage to organs in the collision.
A novice skier, starting from rest, slides down a frictionless 29.0∘ incline whose vertical height is 185 mm. How fast is she going when she reaches the bottom?
Answer:
Her speed when she reaches the bottom of the incline is 1.90 m/s.
Explanation:
Hi there!
To solve this problem, let´s use the energy conservation theorem:
Initially, the skier is at rest at a height of 0.185 m. Since she is at rest, her kinetic energy will be zero and her gravitational potential energy (PE) will be:
PE = m · g · h
Where
m = mass of the skier.
g = acceleration due to gravity.
h = height.
When she reaches the bottom, the height is zero and then the potential energy will be zero. Since there is no friction, the initial potential energy had to be converted into kinetic energy because the total energy of the skier remains constant, i.e., it is conserved.
Then, the final kinetic energy (KE) of the skier has to be equal to the initial potential energy:
PE = KE
The equation of kinetic energy is the following:
KE = 1/2 · m · v²
Then:
KE = PE
1/2 · m · v² = m · g · h
1/2 · m · v² = m · 9.8 m/s² · 0.185 m
v² = 2 · 9.8 m/s² · 0.185 m
v = 1.90 m/s
Her speed when she reaches the bottom of the incline is 1.90 m/s.
You throw a ball straight up, it peaks out, and then cones back down to you. During this motion, the velocity and acceleration
a) always point in the same direction
b) always point in opposite direction
c) sometimes point in the same direction, and other times point in opposite to each other.
d) depends on the way the ball is thrown
e) depends in the mass of the ball
Answer:
The answer is C sometimes point in the same direction, and other times point in opposite to each other.
Explanation:
When you throw a ball straight up velocity direction head up to up side but the acceleration points opposite direction due to gravitation of earth. Gr aviation slows down the ball when it goes up, when it reaches the summit and starts to fall down both velocity and acceleration points the same way. The ball speeds up and drops down.
The velocity and acceleration of a ball thrown straight up sometimes point in the same direction and sometimes in opposite directions. On the way up, they are opposite, but when the ball peaks and begins falling, they align in the same direction (downward). Therefore, the correct answer is that they sometimes point in the same direction and other times in opposite directions.
Explanation:When you throw a ball straight up, it follows a parabolic trajectory due to the influence of gravity. Let's examine the ball's velocity and acceleration throughout its motion:
The ball's velocity is initially positive as it travels upwards after being thrown. When the ball reaches its highest point, its velocity becomes zero as it changes direction.From the moment the ball is released until it hits the ground, the acceleration due to gravity is a constant negative value, directed downward toward the center of the Earth.On the way up, the direction of the ball's velocity (upward) and the direction of acceleration (downward) are opposite. When the ball reaches its peak and starts to fall back down, the velocity (now downward) and the constant acceleration due to gravity (also downward) will be in the same direction.Therefore, during the motion of the ball, the acceleration does not always point in the same direction as the ball's motion. Instead, the direction of velocity and acceleration are opposite on the ascent and the same on the descent. Hence, our answer to the question is that the velocity and acceleration sometimes point in the same direction, and other times point in opposite to each other.
The multi-link mechanism in the Variable Compression Turbo Engine _____, thus varying the compression ratio.
A. Adjusts how far down the piston travels
B. Can change one individual piston's operation independent of the other three
C. Acts like a fixed-length connecting rod
Answer:
A. Adjusts how far down the piston travels
Explanation:
This type of engine changes the possition of the piston in order to modify the compression chamber volume and therefore the compression ratio of the engine. The volume of the chamber is proportional to the run of the piston (how far down the piston travels)
This engine is used to achive the optimal compression rate in each individual stage.
The multi-link mechanism in a Variable Compression Turbo Engine adjusts the piston travel to vary the compression ratio, providing efficient operation under different conditions but does not change individual pistons independently.
The multi-link mechanism in the Variable Compression Turbo Engine adjusts the angle of the connecting rods, which in turn adjusts how far down the piston travels in the cylinder. This adjustment changes the volume of the cylinder when the piston is at the top of its stroke, thus varying the compression ratio. The multi-link mechanism does not act like a fixed-length connecting rod nor can it change one individual piston's operation independent of the others, as all pistons in a multi-cylinder engine are generally interconnected and move synchronously.
By varying the compression ratio, the engine can operate efficiently under a variety of conditions, offering more power when needed or improving fuel efficiency when less power is required. This mechanism is a sophisticated mechanical linkage that transforms the linear motion of the pistons into the rotary motion of the crankshaft, similar to the operation of conventional connecting rods, but with the added capability of adjusting the compression ratio.
Tectonic plates are pieces of the ________ that float on the more fluid ________ below.
Answer:
lithosphere and asthenosphere
Explanation:
Lithosphere is the part of the earth surface which is rigid and hard. It consists of whole crust and the upper mantle.It comprises of number of plates called plate tectonic.
The asthenosphere is the Earth's upper mantle's extremely viscous, mechanically fragile and ductile area. This sits below the lithosphere, some 80 to 200 km below the ground at depths. The boundary between lithosphere and asthenosphere is commonly referred to as LAB.
An object of unknown mass is hung on the end of an unstretched spring and is released from rest. The acceleration of gravity is 9.81 m/s 2 . If the object falls 2.75 cm before first coming to rest, find the period of the motion. Answer in units of s
The question relates to Simple Harmonic Motion of a mass-spring system, and asks to calculate the period of the motion. The approach involves the use of Hooke's law and Newton's second law, and understanding that at maximum amplitude, gravitational potential energy converts to elastic potential energy.
Explanation:The question discusses a concept in physics known as Simple Harmonic Motion, specifically in relation to a mass attached to a spring. The object of unknown mass is hung on the unstretched spring, let go and then allowed to move down under the force of gravity. This object comes to rest for the first time when it has moved to its maximum amplitude, which is given as 2.75 cm. The period of the motion is what we are required to find.
The period of oscillation for a simple harmonic oscillator (in this case, a mass-spring system) can be calculated using the formula T = 2π√(m/k), where m is the mass and k is the spring constant. However, from the given information, we do not have the mass or the spring constant and need an alternative approach.
Let's use Hooke's law (F = kx) and Newton's second law (F = ma). We know that at the maximum amplitude, all the gravitational potential energy is converted to elastic potential energy. We can write mgx = 0.5 kx^2, where g is the acceleration due to gravity and x is the displacement (2.75 cm). From here we can calculate k. Then we substitute this value of k obtained into the formula for T, we could then find the period of the motion of the object.
Learn more about Simple Harmonic Motion here:https://brainly.com/question/28208332
#SPJ12
if you were to look for a cut on the palmar surface of a dog's leg where would you look?
Answer:
If you were to look for a cut on the palmar surface of a dog's leg then you should look at the back area of the front leg below the carpus.
Explanation:
Final answer:
To find a cut on the palmar surface of a dog's leg, you would check the underside of the foreleg where the paw pads are located.
Explanation:
If you want to locate a cut on the palmar surface of a dog's leg, you would look at the underside of the dog's foreleg. In humans, the palmar surface refers to the palm of the hand, and similarly, in quadrupeds like dogs, it refers to the analogous area - the bottom of their paws on the forelegs, where dogs have pads that contact the ground. This is analogous to the palm of the human hand although covered with different skin and touch pads.
Two speakers are spaced 15 m apart and are both producing an identical sound wave. You are standing at a spot as pictured. What would be the frequency produced by the speakers to create perfectly constructive interference? Assume n = 1 and v = 343 m/s
213.04 Hz
256.70 Hz
186.68 Hz
233.14 Hz
Answer:
213.04
Explanation:
Answer:
The correct answer is option 213.04 Hz
Explanation:
Hello!
Let's solve this!
In this link we will find the image of the problem.
https://smart-answers.com/physics/question14138735
Regarding that image, we will first calculate the distance from my position to S1 and then to S2. Then the difference between these results.
We will use pitagoras.
S1 = [tex]\sqrt{10^{2}+22^{2} }[/tex]
S1 = 24.17
S2 = [tex]\sqrt{5^{2}+22^{2} }[/tex]
S2 = 22.56
The difference will be:
24.17-22.56 = 1.61 m
Constructive interference:
Δr=n*λ
λ=1.61 m (for n = 1)
Then we will calculate the frequency:
f = v / λ
f = (343m / s) /1.61m
f = 213.04 Hz
So the correct answer is option 213.04 Hz
A ski jumper has 1.2 x 10 4 J of potential energy at the top of the ski jump. The friction on the jump slope is small, but not negligible. What can you conclude about the ski jumpers kinetic energy at the bottom of the jump?
Answer
kinetic energy will be less than 1.2×10^4 J
Explanation:
as some of this potential energy will be used to over come force of friction , hence by law of conservation of energy , kinetic energy will be less than potential energy at top and will be less than 1.2×10^4 J
Final answer:
The ski jumper's kinetic energy at the bottom of the ski jump will be slightly less than the initial potential energy of 1.2 x 10⁴ J due to the small but non-negligible work done by friction, which converts some of the mechanical energy into other forms like heat and sound.
Explanation:
If a ski jumper has 1.2 x 10⁴ J of potential energy at the top of the ski jump and we take into account that friction is small but not negligible, we can conclude that the ski jumper's kinetic energy at the bottom will be slightly less than 1.2 x 10⁴ J. According to the conservation of energy principle, the sum of potential and kinetic energy in a system should be constant if there is no external work done. However, friction does perform negative work (it removes energy from the system), converting some mechanical energy into heat and sound, and therefore the actual kinetic energy at the bottom will be the initial potential energy minus the energy lost due to friction.
For example, in the given scenario where a ski jumper starts from rest, their initial kinetic energy is zero, and all the energy is in the form of potential energy. As they descend, potential energy is converted into kinetic energy. When friction is present, it will do negative work on the system, represented by a slight decrease in the total mechanical energy by the time the skier reaches the bottom. The kinetic energy of the ski jumper at the bottom would be the initial potential energy minus the work done by friction during the descent.
In a theoretical scenario without friction, the skier's kinetic energy at the bottom would equal their initial potential energy minus zero (since no work is done by friction), resulting in the skier having kinetic energy equal to 1.2 x 10⁴ J at the bottom.
Which of the following statements are true. (Justify your answer to get credit) (5 points)
1. Mechanical energy is conserved before and after the string is cut.
2. Mechanical energy is conserved before the string is cut.
3. Mechanical energy is conserved after the string is cut
4. Linear momentum is conserved 5. Angular momentum is conserved.
Answer:
2 & 3
Explanation:
Since they are all vector quantities, if they remain in a closed system where no external force acts on the system, the vector sum of the momentum remains constant.
When there is no loss or gain in the total vector sum of the energy of the system means it's energy is conserved.
If you place a teaspoon of sugar in the bottom of a glass of water, it will dissolve completely over time. Left longer, eventually the water will disap- pear and the sugar crystals will reappear. Explain these observations in terms of entropy.
Explanation:
It is known that entropy is the degree of randomness. More is the speed of molecules of a substance more will be its degree of randomness. Hence, more will be the entropy of substance.
When we place a teaspoon of sugar in the bottom of a glass of water, it will dissolve completely over time. This dissolution will cause the sugar molecules to spread out in the water.
And, with time water will evaporate and this will lead to the formation of crystals again. This reappearance of sugar crystals will cause a decrease in entropy as there occurs decrease in randomness.
But this decrease in entropy is balanced by increase in the entropy of water molecules as they are evaporating.
The process of sugar dissolving and reappearing in water can be explained in terms of entropy.
Explanation:The process described in the question can be explained in terms of entropy, which is a measure of the disorder or randomness in a system. When the teaspoon of sugar is placed in the water, the sugar crystals break down and mix with the water molecules, increasing the entropy of the system. With time, the water molecules continue to move and mix, increasing the disorder even further.
However, if the water is left to evaporate, the water molecules will escape into the air, and the sugar molecules will not be able to dissolve in the evaporating water. As a result, the sugar crystals will eventually reappear.
Learn more about Entropy here:https://brainly.com/question/17172535
#SPJ3
The force that causes your car to gain momentum when going downhill is known as gravity.True / False.
Answer:
TRUE. The weight component is responsible for acceleration and therefore the increase in vehicle speed,
Explanation:
Let's write Newton's second law for the car down a slope
Y Axis
N-Wy = 0
N = Wy
X axis
Wx -fr= m a
Using trigonometry
sin θ = Wx / W
cos θ = Wy / W
Wx = W sin θ
Wy = W cos θ
We replace
W sin θ - fr = m a
The weight component is responsible for acceleration and therefore the increase in vehicle speed,
fr is the force of car brakes
Consequently, of the above TRUTH
why doesnt the moon get pulled into the sun
Answer:
The moon does not get pulled into the sun because of gravitational pull.
Explanation:
Gravitational pull is a force that pulls things down or into i guess you can say. Like are orbit, all of the planets (even the dwarf planet "pluto") are circling around are sun but we have things called moons that circle are planets. Are moon is orbiting us like we (are earth) are orbiting the sun. So to get into a little more detail, i will add that we circle the sun or the moon circles us because the action of earth pulling away from the suns gravitational pull is causing it to either rotate or revolve.So we are stuck in the gravitational force of the sun and the moon is stuck in ares. But as someone who LOVES astronamy will say that i watched a video about are earth, sun, and moon and it said that each year are moon is slowly pulling away from the earth. sooner or later we might not have a solar or lunar eclipse anymore.
Answer:
But the path of the Moon is always concave towards the Sun; the gravitational force exerted by the Sun on the Moon is always greater than the pull of the Earth on the Moon
Explanation:
You have a special lightbulb with a very delicate wire filament. The wire will break if the current in it ever exceeds 1.90 A , even for an instant. What is the largest root-mean-square current you can run through this bulb? _______A
Answer: 1.34A
Explanation:
Since the wire will break if it exceeds 1.90A current, this will be the maximum current needed.
The root mean square current
Irms = I0/√2
Where I0 is the maximum current given
Irms = 1.90/√2
Irms = 1.34A
As a way of determining the inductance of a coil used in a research project, a student first connects the coil to a 9.7 V battery and measures a current of 0.742 A. The student then connects the coil to a 27.3 V(rms), 51.1 Hz generator and measures an rms current of 0.429 A. What is the inductance?
Answer:
L = 0.194 H
Explanation:
given,
Voltage = 9.7 V
current = 0.742 A
R = 9.7 V / 0.742 A
R = 13.07 Ohms.
the A.C. impedance of the inductor, like this:
Z = V / I
Z = 27.3 V / 0.429 A
Z = 63.64 Ohms.
now,
inductive reactance, X_L
[tex]X_L = \sqrt{Z^2 - R^2}[/tex]
[tex]X_L = \sqrt{63.64^2 - 13.07^2}[/tex]
[tex]X_L =62.28\ \Omega[/tex]
[tex]X_L = 2\pi f \times L[/tex]
[tex]L = \dfrac{X_L}{2\pi f}[/tex]
[tex]L = \dfrac{62.28}{2\pi \times 51.1}[/tex]
L = 0.194 H
A length of copper wire has a resistance 44 Ω. The wire is cut into three pieces of equal length, which are then connected as parallel lengths between points A and B. What resistance will this new "wire" of length L0 3 have between points A and B? Answer in units of Ω.
Answer:
[tex]\frac{R}{1} = \frac{44}{9}\ohm[/tex]
Explanation:
Let us imagine that there are three wire of length equal length having equal resistances each of 44/3 Ω
Now connect these wires in parallel to so that their equivalent resistance is R.
then
[tex]\frac{1}{R} = \frac{1}{R_1}+\frac{1}{R_2}+\frac{1}{R_3}[/tex]
[tex]\frac{1}{R} = \frac{3}{44}+\frac{3}{44}+\frac{3}{44}[/tex]
[tex]\frac{1}{R} = \frac{9}{44}[/tex]
⇒[tex]\frac{R}{1} = \frac{44}{9}\ohm[/tex]
Answer:
4.89 Ω
Explanation:
we know that resistance is directly proportional to length. hence as the wire is cut in three pieces, the resistance of each piece becomes one-third of the original resistance of the wire.
[tex]R[/tex] = Resistance of wire = 44 Ω
[tex]r[/tex] = resistance of each piece
Resistance of each piece is given as
[tex]r = \frac{R}{3}\\r = \frac{44}{3}[/tex]
The three pieces are connected in parallel,
[tex]R_{p}[/tex] = Resistance of parallel combination of three pieces
Resistance of parallel combination is given as
[tex]\frac{1}{R_{p}}= \frac{1}{r} + \frac{1}{r} + \frac{1}{r} \\\frac{1}{R_{p}}= \frac{3}{r}\\R_{p}= \frac{r}{3}\\R_{p} = \frac{\frac{44}{3} }{3}\\R_{p} = \frac{44}{9} \\R_{p} = 4.89 ohm[/tex]
Suppose we imagine the Sun to be about the size of a grapefruit. How big an area would the orbits of the nine planets of the Solar System cover?
Answer:
size at this scale of the solar system is 10⁸ m²
Explanation:
For this exercise we can use a direct proportions rule or rule of three.
If the radius of the Sun is 7 10⁸ m is equal to the radius of a grapefruit is on average about 5 cm, the radius of the orbit of the plant is x
Mercury
r1 = 5.8 10¹⁰m
x = r1 / r_Sum 5
x = 5.8 10¹⁰/7 10⁸
x = 82 m
We repeat the same formula with all the radii of the orbit, the results in the table
Numb name r_orbit (m) x (m) A (m2)
0 Sun 7 10⁸ 1 3.14
1 mercury 5.8 10¹⁰ 8.2 10¹ 2.0 10⁴
2 venus 1 10¹¹ 1.4 10² 6.2 10⁴
3 Earth 1.5 10¹¹ 2.1 10² 1.4 10⁵
4 Mars 2.3 10¹¹ 3.2 10² 3.2 10⁵
5 Jupiter 7.8 10¹¹ 1.1 10³ 3.8 10⁶
6 Saturn 1.4 10¹² 2 10³ 1.3 10⁷
7 Uranus 2.9 10¹² 4.1 10³ 5.3 10⁷
8 Neptune 4.5 10¹² 6.4 10³ 1.3 10⁸
9 Pluto 5.9 10¹² 8.4 10³ 2.2 10⁸
The area of a circle is
A = π R²
Mercury
A = π 80²
A = 2.0 14 m²
The other values are in the table
The size at this scale of the solar system is 10⁸ m²
What is the specific fuel requirement for flight under VFR at night in an airplane?
A) Enough to fly to the first point of intended landing and to fly after that for 45 minutes at normal cruising speed.
B) Enough to complete the flight at normal cruising speed with adverse wind conditions.
C) Enough to fly to the first point of intended landing and to fly after that for 30 minutes at normal cruising speed.
Answer:
A). Enough to fly to the first point of intended landing and to fly after that for 45 minutes at normal cruising speed
Explanation:
Here are Fuel requirements for flight in VFR conditions
No person may begin a flight in an airplane under VFR conditions unless there is enough fuel to fly to the first point of intended landing and, assuming normal cruising speed -
During the day, to fly after that for at least 30 minutes; or At night, to fly after that for at least 45 minutes.An adult generates 72 W of power as she pulls a sled forward across a flat snowy surface with a force of 80 N. The adult pulls with this force for 4.5 minutes. What distance does the sled move?
130 m
280 m
240 m
180 m
Answer:
240 m
Explanation:
Gradpoint
Final answer:
To calculate the distance the sled moves, use the formula Work = Force x Distance and substitute the given values to find the answer as 240 meters.
Explanation:
Power is a physical quantity that represents the rate at which work is done or energy is transferred or converted. Mathematically, power is defined as the amount of energy transferred or converted per unit time. It is typically measured in watts (W), where 1 watt is equivalent to 1 joule per second. In other words, power indicates how quickly work is done or energy is transferred.
To find the distance the sled moves, we can use the formula:
Work = Force x Distance
Given: Power = 72 W, Force = 80 N, Time = 4.5 minutes = 270 seconds
Work = Power x Time = 72 W x 270 s = 19440 J
Distance = Work / Force = 19440 J / 80 N = 243 m
Therefore, the sled moves a distance of 240 meters.