How much work does it take for an external agent to move a 45.0-nC charge from a point on the +x-axis, 3.40 cm from the origin to a point halfway between the 41.0-nC and 52.0-nC charges?

Answer:

687,500 N

Explanation:

Workdone = Force × Distance

Making force the subject of the formula; we have:

Force =[tex]\frac{workdone}{distance}[/tex]

Given that:

workdone  = 5.5×10⁵ J

Distance = 0.80 m

∴ Force = [tex]\frac{5.5*10^5}{0.8}[/tex]

Force = 687,500 N

Answer:

6.875×10⁵  N.

Explanation:

Force: This can be defined as the product of mass and acceleration or it can be defined as the ratio of work done and distance. The S.I unit of force is Newton.

W = F×d................. Equation 1

Where W = work done, F = force, d = distance.

make F the subject of the equation

F = W/d.................... Equation 2

Given: W = 5.5×10⁵ J, d = 0.8 m

Substitute into equation 2

F =  5.5×10⁵ /0.8

F = 6.875×10⁵  N.

Hence the force exerted on the truck by the sand = 6.875×10⁵  N.

Answer:

Resistance increases with increase in temperature which depends on power supplied which also depends on voltage.

Thermal expansion will make resistance larger.

Explanation:

Light bulb is a good example of a filament lamp. If we plot the graph of voltage against current we will notice that resistance is constant at constant temperature.

The filament heats up when an electric current passes through it, and produces light as a result.

The resistance of a lamp increases as the temperature of its filament increases. The current flowing through a filament lamp is not directly proportional to the voltage across it.

tensile stress begins to appear in resistor as the temperature rises. Thus, the resistance value increases as the temperature rises. Resistance value can only decrease as the temperature rises in case of thin film resistor with aluminium substrate.

In case of a filament bulb, the resistance will increase as increase in length of the wire. The thermal expansion in this regard is linear expansivity in which resistance is proportional to length of the wire.

Resistance therefore get larger.

Answer: tensional force

Explanation:

Tension force on a material occurs when two equal forces act on a material in an opposite direction away from the ends of the material.

Pre-tensing a wire material increases its load bearing capacity and reduces its flexure.

Answer:

Please find attached

Explanation:

The acceleration of the block B is 0.69 m/s² downwards in the direction of block B.

The normal force on each block is calculated as follows;

[tex]F_n_ A = mgcos \theta\\\\F_n_ B = m_ B g[/tex]

The frictional force on block A  is calculated as;

[tex]F_f = \mu_k F_n\\\\F_f = \mu_ kg mgcos \theta[/tex]

The horizontal force on block A is given as;

[tex]F_x = mgsin\theta[/tex]

The tension on the string due to each block is given as;

[tex]T_ A = m_ A a\\\\T_ B = m_ B a[/tex]

The net force on the block B is calculated as;

[tex]m_Bg - (T_A + m_Agsin\theta + \mu mgcos\theta) = T_B\\\\m_Bg - m_Agsin\theta - \mu mgcos\theta= T_B + T_ A\\\\m_Bg - m_Agsin\theta - \mu mgcos\theta = a(m_ B+ m_ A)\\\\a = \frac{m_Bg - m_Agsin\theta - \mu mgcos\theta}{m_B + m_ A} \\\\a = \frac{(8)(9.8)\ -\ (10)(9.8)(sin30)\ -\ (0.2)(10)(9.8)(cos30)}{8 + 10} \\\\a = 0.69 \ m/s^2 \ (in -direction \ of \ block \ B)[/tex]

Thus, the acceleration of the block B is 0.69 m/s² downwards in the direction of block B.

Learn more here:https://brainly.com/question/15412658

Answer:

The voltage will be 0.0125V

Explanation:

See the picture attached

Answer:

[tex]1.5\times 10^{11}}[/tex]

Explanation:

We are given that

Electric field=[tex]E=3\times 10^6 N/C[/tex]

Dimension of parallel plate capacitor=[tex]3 cm\times 3 cm[/tex]

Area of parallel plate capacitor=[tex]A=3\times 3=9 cm^2=9\times 10^{-4}m^2[/tex]

[tex]1 cm^2=10^{-4} m^2[/tex]

We have to find the number of electrons must be transferred from one electrode to the other to create  a spark between the electrodes.

[tex]E=\frac{Q}{\epsilon_0A}[/tex]

Where [tex]\epsilon_0=8.85\times 10^{-12}C^2/Nm^2[/tex]

Substitute the values

[tex]3\times 10^6=\frac{Q}{8.85\times 10^{-12}\times 9\times 10^{-4}}[/tex]

[tex]Q=3\times 10^6\times 8.85\times 10^{-12}\times 9\times 10^{-4}}[/tex]

[tex]Q=2.4\times 10^{-8} C[/tex]

We know that

[tex]Q=ne=n\times 1.6\times 10^{-19} [/tex]

Where e=[tex]1.6\times 10^{-19} C[/tex]

[tex]n=\frac{Q}{e}=\frac{2.4\times 10^{-8}}{1.6\times 10^{-19}}=1.5\times 10^{11}}[/tex]

Answer:

The induced emf 1.43 s after the circuit is closed is 4.19 V

Explanation:

The current equation in LR circuit is :

[tex]I=\frac{V}{R} (1-e^{\frac{-Rt}{L} })[/tex]    .....(1)

Here I is current, V is source voltage, R is resistance, L is inductance and t is time.

The induced emf is determine by the equation :

[tex]V_{e}=L\frac{dI}{dt}[/tex]

Differentiating equation (1) with respect to time and put in above equation.

[tex]V_{e}= L\times\frac{V}{R}\times\frac{R}{L}e^{\frac{-Rt}{L} }[/tex]

[tex]V_{e}=Ve^{\frac{-Rt}{L} }[/tex]

Substitute 6.05 volts for V, 0.655 Ω for R, 2.55 H for L and 1.43 s for t in the above equation.

[tex]V_{e}=6.05e^{\frac{-0.655\times1.43}{2.55} }[/tex]

[tex]V_{e}=4.19\ V[/tex]

Based on the calculations, the induced emf is equal to 4.19 Volts.

Given the following data:

In a RL circuit, current is given by this mathematical expression:

[tex]I=\frac{V}{R} (1-e^{\frac{Rt}{L} })[/tex]

Where:

For an induced emf in a circuit, we have:

[tex]E=L\frac{dI}{dt} \\\\E=L \times I \\\\E=L \times \frac{V}{R} (1-e^{\frac{-Rt}{L} })\\\\E=V e^{\frac{-Rt}{L} }\\\\E=6.05 e^{\frac{-0.655 \times 1.43}{2.55} }[/tex]

E = 4.19 Volts.

Read more current here: https://brainly.com/question/25813707

Complete Question:

Two 3.0µC charges lie on the x-axis, one at the origin and the other at 2.0m. A third point is located at 6.0m. What is the potential at this third point relative to infinity? (The value of k is 9.0*10^9 N.m^2/C^2)

Answer:

The potential due to these charges is 11250 V

Explanation:

Potential V is given as;

[tex]V =\frac{Kq}{r}[/tex]

where;

K is coulomb's constant = 9x10⁹ N.m²/C²

r is the distance of the charge

q is the magnitude of the charge

The first charge located at the origin, is 6.0 m from the third charge; the potential at this point is:

[tex]V =\frac{9X10^9 X3X10^{-6}}{6} =4500 V[/tex]

The second charge located at 2.0 m, is 4.0 m from the third charge; the potential at this point is:

[tex]V =\frac{9X10^9 X3X10^{-6}}{4} =6750 V[/tex]

Total potential due to this charges  = 4500 V + 6750 V = 11250 V

The potential due to two 3.0 μC charges on the x-axis at different distances from a point can be calculated using Coulomb's Law.

The potential due to two point charges can be found using Coulomb's Law. The potential, V, at a point on the x-axis is the sum of the potentials from each charge. The potential due to a point charge can be calculated using the formula V = k * (Q / r), where k is the electrostatic constant, 9 x 10^9 Nm^2/C^2, Q is the charge, and r is the distance between the charge and the point. In this case, since the charges are on the x-axis, the distance between the origin and the point is x, and the distance between the other charge and the point is (6-x). So, the potential at the point is V = k * (3.0 x 10^-6 / x) + k * (3.0 x 10^-6 / (6-x)) relative to infinity.

Learn more about potential here:

https://brainly.com/question/28300184

#SPJ3

Explanation:

Below is an attachment containing the solution.

The resultant voltage depends on the arrangement of the batteries. For series configuration, the voltage sums up to 9V. For parallel, it remains 1.5V. And for combined series and parallel, it sums up to 3V.

The voltage across batteries depends on how they are connected.

https://brainly.com/question/31347497

#SPJ3

Answer:

3.41m

Explanation:

The following were obtained from the question:

f (frequency) = 8.81x10^7Hz

V (velocity of electromagnetic wave) = 3x10^8 m/s

λ (wavelength) =?

Velocity, frequency and wavelength of a wave are related with the equation below:

V = λf

λ = V/f

λ = 3x10^8 /8.81x10^7

λ = 3.41m

Therefore, the wavelength of the radio wave is 3.41m

Answer:

Answer: 3.41

Explanation:

Edge 2020 (E2020)

Answer:

Explanation:

The dimness of two light source, which have the same intensify depends on their distance from the observer. That is why some stars appear brighter than the others, this is due to the distance of each of them from the earth.

The closer a light source, the brighter they appear

Now, if the right lamp has a dim light actually, it shows that the bicycle is closer than it appears.

Answer:

[tex]W = 10.28\ mm[/tex]

Explanation:

Given,

Red light wavelength = 633 nm

width of slit = 0.320 mm

distance,d = 2.60 m

Condition of first maximum

[tex]a sin \theta_1 = m\lambda [/tex]

[tex]\theta_1 =sin^{-1}(\dfrac{m\lambda}{a})[/tex]

m = 1

[tex]\theta_1 =sin^{-1}(\dfrac{633\times 10^{-9}}{0.32\times 10^{-3}})[/tex]

[tex]\theta_1 = 0.1133^\circ[/tex]

Width of the first minima

[tex]y_1 = L tan \theta_1[/tex]

[tex]y_1 = 2.60\times tan( 0.11331)[/tex]

[tex]y_1 = 5.14 \ mm[/tex]

Now, width of the central region

[tex]W = 2 y_1[/tex]

[tex]W = 2\times 5.14[/tex]

[tex]W = 10.28\ mm[/tex]

For a square in an electric field, the potential difference between points C and D is the same as that between A and B, and the potential difference between A and D is zero.

To answer these questions, we first need to understand the concept of electric potential difference, or voltage. It's defined as the change in potential energy of a charge moved between two points, divided by the charge. In the case of a square area in an electric field, if the potential difference between points A and B (ΔV_AB) and between B and D (ΔV_BD) is x volts, then the potential difference between A and C (ΔV_AC) is -x volts, as it's negative of ΔV_AB. Due to this, the potential difference between C and D (ΔV_CD) would be also x volts as it's same as that between A and B and equal to ΔV_BD.

For Part C of the question, thinking about the square as a cycle, if we traverse from A to B to D (or vice versa) the total potential difference would be x - x = 0 volts. Therefore, the potential difference between A and D (ΔV_AD) is zero.

https://brainly.com/question/27091481

#SPJ12

Answer:

vi = 4.77 ft/s

Explanation:

Given:

- The radius of the surface R = 1.45 ft

- The Angle at which the the sphere leaves

- Initial velocity vi

- Final velocity vf

Find:

Determine the sphere's initial speed.

Solution:

- Newton's second law of motion in centripetal direction is given as:

                         m*g*cos(θ) - N = m*v^2 / R

Where, m: mass of sphere

             g: Gravitational Acceleration

             θ: Angle with the vertical

             N: Normal contact force.

- The sphere leaves surface at θ = 34°. The Normal contact is N = 0. Then we have:

                         m*g*cos(θ) - 0 = m*vf^2 / R

                         g*cos(θ) = vf^2 / R    

                         vf^2 = R*g*cos(θ)

                         vf^2 = 1.45*32.2*cos(34)

                        vf^2 = 38.708 ft/s

- Using conservation of energy for initial release point and point where sphere leaves cylinder:

                          ΔK.E = ΔP.E

                          0.5*m* ( vf^2 - vi^2 ) = m*g*(R - R*cos(θ))

                          ( vf^2 - vi^2 ) = 2*g*R*( 1 - cos(θ))

                          vi^2 =  vf^2 - 2*g*R*( 1 - cos(θ))

                          vi^2 = 38.708 - 2*32.2*1.45*(1-cos(34))

                          vi^2 = 22.744

                           vi = 4.77 ft/s

Answer:

577g

Explanation:

Given parameters:

Temperature change = 5.9°C

Amount of heat lost = 427J

Unknown:

Mass of the block = ?

Solution:

The heat capacity of a body is the amount of heat required to change the temperature of that body by 1°C.

                H =  m c Ф

  H is the heat capacity

 m  is the mass of the block

  c is the specific heat capacity

   Ф is the temperature change

Specific heat capacity of lead is 0.126J/g°C

   m = H / m Ф

   m = [tex]\frac{427}{0.126 x 5.9}[/tex]  = 577g

Mass of the lead block is 577g

Answer: 0.5654

Explanation:

Answer:

from the quarter to the block of ice

Explanation:

Heat flows from higher temperature to lower temperature until temperature of both bodies are in Equilibrium .

Since block of ice has lower temperature than that of quarter. heat transfer will take from quarter to ice until both have same temperature(in other words temperature are in Equilibrium for quarter and ice)

Final answer:

Heat will flow from the hot quarter to the block of ice as heat always transfers from a warmer object to a cooler one. The ice absorbs the heat and may melt without increasing in temperature due to the phase change.

Explanation:

When a hot quarter is dropped onto a large block of ice, heat will flow from the quarter to the block of ice. This is because heat always flows spontaneously from a hotter object to a cooler one according to thermodynamics. In this case, the hot quarter would lose heat, and the block of ice would absorb it. Even as the ice absorbs heat, it may not increase in temperature as it may be undergoing a phase change from solid to liquid at 0°C. The heat is used to break the bonds between water molecules during the melting process, thus increasing the internal potential energy instead of increasing the kinetic energy, which would raise the temperature.

Answer:

Explanation:

net force exerted on charge Q₃, exerted by charges Q₁and Q₂, will be  zero

if net  electric field due to charges Q₁ and Q₂  at origin is zero .

electric field due to Q₂

= 9 X 10⁹ X 3 x10⁹ / .04²

electric field due to Q₁

= 9 X 10⁹ X Q₁ / .02²

For equilibrium

9 X 10⁹ X Q₁ / .02² = 9 X 10⁹ X 3 x10⁻⁹ / .04²

Q₁  = 3 X10⁻⁹ x .02² / .04²

= 3 / 4 x 10⁻⁹

.75 x 10⁻⁹  C

Answer:

[tex]\dot V = 0.542 \frac{m^{3}}{s}[/tex]

Explanation:

The power needed for the pump to raise the pressure of gasoline is defined by following equation. The maximum possible volume flow rate is isolated and then calculated:

[tex]\dot W = \dot V \cdot \Delta P\\\dot V = \frac{\dot W}{\Delta P}\\\dot V = \frac{3.8 kW}{7 kPa}\\\dot V = 0.542 \frac{m^{3}}{s}[/tex]

Explanation:

Below is an attachment containing the solution.

Answer:

4 A

Explanation:

We are given that

[tex]R_1=R_2=R_3=4\Omega[/tex]

I=12 A

We have to find the current flowing through each resistor.

We know that in parallel combination current flowing through different resistors are different and potential difference across each resistor is same.

Formula :

[tex]\frac{1}{R}=\frac{1}{R_1}+\frac{1}{R_2}+\frac{1}{R_3}[/tex]

Using the formula

[tex]\frac{1}{R}=\frac{1}{4}+\frac{1}{4}+\frac{1}{4}=\frac{3}{4}[/tex]

[tex]R=\frac{4}{3}\Omega[/tex]

[tex]V=IR[/tex]

Substitute the values

[tex]V=12\times \frac{4}{3}=16 V[/tex]

[tex]I_1=\frac{V}{R_1}=\frac{16}{4}=4 A[/tex]

[tex]I_1=I_2=I_3=4 A[/tex]

Hence, current flows through any one of the resistors is 4 A.

The current flows through a resistor is equal to 4A.

To understand more, check below explanation.

When n number of resistors are connected in parallel to a battery  and current I flowing in the circuit.

Then, current flows in each resitor [tex]=\frac{I}{n}[/tex]

It is given that, three identical resistors are connected in parallel to a battery and total current of 12A flows through the circuit.

So that, current in each resistor [tex]=\frac{12}{3}=4A[/tex]

Hence, the current flows through a resistor is equal to 4A.

Learn more about the resistors here:

https://brainly.com/question/24858512

Answer:

[tex]3.7\times10^{35}\text{ kg m/s}[/tex]

Explanation:

The system of the colliding bodies is ideally isolated, so no external forces act on it. By the principle of conservation of linear momentum, the total initial momentum is equal to the total final momentum.

Both bodies had a head-on collision. We take the direction of the faster body as the positive direction. Because they have the same mass, let's call this mass m.

Hence, we have for the initial momentum

[tex]69m - 56m = 13m[/tex]

The final momentum is

[tex](m+m) \times4 =[/tex]8m

The difference in both momenta is the momentum carried by the gravitational waves.

[tex]13 m - 8m = 5m[/tex]

Converting to the appropriate units and using the actual value of m (37 × a solar mass), we have

[tex]5\times10^3 \text{ m/s}\times37\times2\times10^{30} \text{ kg} = 3.7\times10^{35}\text{ kg m/s}[/tex]

Answer:

[tex]\frac{Q}{Q_0}=1[/tex]

Explanation:

Capacitance is defined as the charge divided in voltage.

[tex]C=\frac{Q}{V}(1)[/tex]

Introducing a dielectric into a parallel plate capacitor decreases its electric field. Therefore, the voltage decreases, as follows:

[tex]V=\frac{V_0}{k}[/tex]

Where k is the dielectric constant and [tex]V_0[/tex] the voltage of the capacitor without a dielectric

The capacitance with a dielectric between the capacitor plates is given by:

[tex]C=kC_0[/tex]

Where k is the dielectric constant and [tex]C_0[/tex] the capacitance of the capacitor without a dielectric. So, we have:

[tex]Q=CV\\Q=kC_0\frac{V_0}{k}\\Q=C_0V_0\\Q_0=C_0V_0\\Q=Q_0\\\frac{Q}{Q_0}=1[/tex]

Therefore, a capacitor with a dielectric stores the same charge as one without a dielectric.

The velocity of A is 5.16m/s²

Explanation:

Given-

mass of cylinder A, mₐ = 2kg

mass of cylinder B, mb = 10kg

Distance, s = 2m

Velocity of A, v = ?

Let acceleration due to gravity, g = 10m/s²

We know,

[tex]a = \frac{mb * g - ma * g}{ma + mb} \\\\a = \frac{10 * 10 - 2 * 10}{ 2 + 10} \\\\a = \frac{80}{12} \\\\a = 6.67m/s^2[/tex]

We know,

[tex]v = \sqrt{2as}[/tex]

[tex]v = \sqrt{2 X 6.67 X 2} \\\\v = \sqrt{26.68} \\\\v = 5.16m/s^2[/tex]

Therefore, the velocity of A is 5.16m/s²

Answer:

 φ = √2/L sin (kx),   E = (h² / 8 mL²) n²  

Explanation:

The Schrödinger equation for a particle in a box is, described by a particle within a potential for simplicity with infinite barrier

      V (x) =   ∞            x <0

                    0      0 <x <L

                    ∞           x> L

This means that we have a box of length L

We write the equation

              (- h’² /2m  d² / dx² + V) φ = E φ

             h’= h / 2π

The region of interest is inside the box, since being the infinite potential there can be no solutions outside the box. The potential is zero

                - h’² /2m d²φ/ dx² = E φ

The solution for this equation is a sine wave,

Because it is easier to work with exponentials, let's use the reaction between the sine function and cook with the exponential

               [tex]e^{ikx}[/tex] = cos kx + i sin kx

Let's make derivatives

              dφ / dx = ika e^{ikx}

              d²φ / dx² = (ik) e^{ikx} = - k² e^{ikx}

Let's replace

            - h'² / 2m (-k² e^{ikx}) = E e^{ikx}

            E = h'² / 2m    k²

To have a solution this expression

Now let's work on the wave function, as it is a second degree differential bond, two solutions must be taken

             φ = A e^{ikx} + B e^{-ikx}

This is a wave that moves to the right and the other to the left.

Let's impose border conditions

         φ (0) = 0

         φ (L) = 0

For being the infinite potential

With the first border condition

         0 = A + B

         A = -B

They are the second condition

         0 = A e^{ikL}+ B e^{-ikL}

We replace

        0 = A (e^{ikL} - e^{-ikL})

We multiply and divide by 2i, to use the relationship

        sin kx = (e^{ikx} - e^{-ikx}) / i2

        0 = A 2i sin kL

Therefore kL = nπ

         k = nπ / L

The solution remains

         φ = A sin (kx)

        E = (h² / 8 mL²) n²

To find the constant A we must normalize the wave function

       φ*φ = 1

       A² ∫ sin² kx dx = 1

We change the variable

       sin² kx = ½ (1 - cos 2kx)

       A =√ 2 / L

The definitive function is

          φ = √2/L sin (kx)

a) 37.9 m/s

b) 1.35 rad below horizontal

c) 7.56 s

Explanation:

a-c)

At the beginning, both the owl and the vole are travelling in a horizontal direction at a speed of

[tex]v_x=8.3 m/s[/tex]

After the vole wiggles free, the owl takes 2 seconds to react; the horizontal distance covered by the owl during this time is

[tex]d_x = v_x t =(8.3)(2)=16.6 m[/tex]

The vertical motion of the wiggle is a free fall motion, so it is a uniformly accelerated motion with constant acceleration

[tex]g=9.8 m/s^2[/tex] in the downward direction

The wiggle falls from a height of h' = 282 m to a height of h = 2 m, so the vertical displacement is

s = h' - h = 282 - 2 = 280 m

The time it takes the wiggle to cover this distance is given by the suvat equation:

[tex]s=u_y t - \frac{1}{2}gt^2[/tex]

where [tex]u_y = 0[/tex] is the initial vertical velocity. Solving for t,

[tex]t=\sqrt{\frac{2s}{g}}=\sqrt{\frac{2(280)}{9.8}}=7.56 s[/tex]

The owl must cover the vertical distance of 280 m in this time interval, so its vertical speed must be:

[tex]v_y=\frac{s}{t}=\frac{280}{7.56}=37.0 m/s[/tex]

Therefore, the speed of the owl during the dive is the resultant of the velocities in the two directions:

[tex]v=\sqrt{v_x^2+v_y^2}=\sqrt{8.3^2+37.0^2}=37.9 m/s[/tex]

b)

In part a-c, we calculated that the components of the velocity of the owl in the horizontal and vertical direction, and they are

[tex]v_x=8.3 m/s\\v_y=37.0 m/s[/tex]

This means that the angle of the owl's dive, with respect to the original horizontal direction, is

[tex]\theta=tan^{-1}(\frac{v_y}{v_x})[/tex]

And substituting these values, we find:

[tex]\theta=tan^{-1}(\frac{37.0}{8.3})=77.4^{\circ}[/tex]

And this angle is below the horizontal direction.

Converting into radians,

[tex]\theta=77.4\cdot \frac{2\pi}{360}=1.35 rad[/tex]

Final answer:

The owl's dive speed is 7.15 m/s, dive angle is 30 degrees below the horizontal, and it takes about 1.76 seconds for the mouse to fall.

Explanation:

The owl's dive speed: Using the equation of motion for constant acceleration, we can find that the owl's dive speed is 7.15 m/s.

The owl's dive angle below the horizontal: The owl's dive angle is 30 degrees above the horizontal when diving.

How long the mouse falls: Applying the kinematic equation for vertical motion, the time it takes for the mouse to fall completely is approximately 1.76 seconds.

Answer:

Explanation:

Mutual inductance is FLUX  induced in second coil due to unit current passed in first coil .

Let i be the current in the bigger coil.

magnetic field  at its center

B = μ₀ n i , n is no of turns per unit length

= μ₀ (N / L) i

Magnetic flux associated with small coil placed near its axis

= B X πR² X N

=μ₀ (N / L) i X πR² X N

FLUX = μ₀ (N² / L) i X πR²

FLUX induced by unit current

M = μ₀ (N² / L)  X πR²

Answer:

121550 J

Explanation:

Parameters given:

Mass, m = 0.34kg

Specific heat capacity, c = 14300 J/kgK

Change in temperature, ΔT = 25K

Heat gained/lost by an object is given as:

Q = mcΔT

Since ΔT is positive in this case and also because we're told that heat was transferred to the hydrogen sample, the hydrogen sample gained heat. Therefore, Q:

Q = 0.34 * 14300 * 25

Q = 121550J or 121.55 kJ

Answer:

It is the same.

Explanation:

        [tex]\Delta K + \Delta U = 0[/tex]

        [tex]\Delta K = K_{f} - K_{0} = \frac{1}{2} * m*v_{f} ^{2} (1)[/tex]

        [tex]\Delta K = -\Delta U = m*g*h (2)[/tex]

Despite the difference in angle, the speed of the objects at the bottom of the planes will be the same because they start with the same potential energy at the top that's entirely converted to kinetic energy (the energy of motion) by the bottom, so long as energy losses are ignored.

The subject of this question lies in the realm of Physics, specifically involving principles of mechanical energy and gravitational potential energy. In the stated scenario, the two objects start on their respective inclined planes from a state of rest. Accordingly, they possess potential energy but no kinetic energy.

As the objects slide down their respective planes, this potential energy is converted into kinetic energy—the energy of motion. Because the two planes are of identical height (thus imparting the same initial potential energy to the objects), and because all potential energy will have been converted to kinetic energy by the time the objects reach the bottom (ignoring energy losses due to friction or air resistance), both objects will possess the same kinetic energy—and thereby the same speed—at the bottom of their planes, regardless of the angle of inclination.

In practical applications, friction and other factors may have a role and might cause the object on the steeper plane (Plane A) to reach the bottom more quickly. However, that's not due to a difference in speed at the bottom; it's about the time taken to get there.

https://brainly.com/question/21487030

#SPJ12

Answer:

D) the masses of the atoms and the strength of the bond.

Explanation:

Mostly in diatomic and triatomic molecules, bonds of the molecules experience vibrations and rotations. When there is a continuous change in the bond distance of the two atoms then these vibrations are termed as stretching vibrations.

As these vibrations exist in the bonds between the atoms. So they depend upon the masses of the atoms and strength of the bonds. Greater masses of the atoms and strong bond strength will result in reduction of vibration. Thats why we don't observe such stretching vibrations in larger, massive molecules. They mostly exists in the diatomic and triatomic molecules where the bond strength is not that much stronger and the masses of the atoms are small.

Answer:

The diameter is  0.8376 m

Explanation:

Magnetic force is the force that is associated with the magnetic field, the magnitude of the magnitude force can be obtained using equation 1;

F = q v B  .....................................1,

where q is the magnitude of the charge of the particle =;

v is the  velocity and;

B is the magnetic field = 1.833 T ;

Here, the path of the charge is circular so the  force can be also considered as the centripetal force  which is represented in equation 2;

[tex]F_{c}[/tex] = m [tex]v^{2}[/tex] / r ....................................2,

m is the particle's mass = 2.00 x[tex]10^{-26}[/tex] kg

v is the speed of ion =  2.05% of 3.00 x [tex]10^{8}[/tex] = 0.0205 x 3.00 x [tex]10^{8}[/tex]

                                    = 6.15 x  [tex]10^{6}[/tex] m/s ;

Singly charged ion has a charge equal to the electron charge and the magnitude = 1.60217646 ×[tex]10^{-19}[/tex] C and;

r is the radius of the circular path.

to get  the diameter of the orbit  we equate equation 1 to 2 and isolate r in equation 2.

q v B = m [tex]v^{2}[/tex] / r

r = m v/q B.....................................3

r = (2.00 x[tex]10^{-26}[/tex] kg) x (6.15 x  [tex]10^{6}[/tex] m/s)  / (1.60217646 ×[tex]10^{-19}[/tex]  C) x (1.833 T)

r = 0.4188 m

The diameter is r x 2

D = 0.4188 m x 2

D = 0.8376 m

Therefore the diameter is  0.8376